Диск или контролер?

А smart чо?

Это смарт полностью:

=== START OF INFORMATION SECTION ===

Device Model: SPCC Solid State DiskB28

Serial Number: 12010653092000000056

Firmware Version: 111118

User Capacity: 128,035,676,160 bytes

Device is: Not in smartctl database [for details use: -P showall]

ATA Version is: 8

ATA Standard is: Exact ATA specification draft version not indicated

Local Time is: Tue Dec 25 14:31:27 2012 EET

SMART support is: Available - device has SMART capability.

SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===

SMART overall-health self-assessment test result: PASSED

General SMART Values:

Offline data collection status: (0x00) Offline data collection activity

was never started.

Auto Offline Data Collection: Disabled.

Self-test execution status: ( 92) The previous self-test completed having

the electrical element of the test

failed.

Total time to complete Offline

data collection: ( 30) seconds.

Offline data collection

capabilities: (0x1b) SMART execute Offline immediate.

Auto Offline data collection on/off support.

Suspend Offline collection upon new

command.

Offline surface scan supported.

Self-test supported.

No Conveyance Self-test supported.

No Selective Self-test supported.

SMART capabilities: (0x0003) Saves SMART data before entering

power-saving mode.

Supports SMART auto save timer.

Error logging capability: (0x01) Error logging supported.

General Purpose Logging supported.

Short self-test routine

recommended polling time: ( 1) minutes.

Extended self-test routine

recommended polling time: ( 1) minutes.

SMART Attributes Data Structure revision number: 16

Vendor Specific SMART Attributes with Thresholds:

ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE

1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 16777215

2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0

3 Spin_Up_Time 0x0007 100 100 050 Pre-fail Always - 0

5 Reallocated_Sector_Ct 0x0013 100 100 050 Pre-fail Always - 0

7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0

8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0

9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 4333

10 Spin_Retry_Count 0x0013 100 100 050 Pre-fail Always - 0

12 Power_Cycle_Count 0x0012 100 100 000 Old_age Always - 13

168 Unknown_Attribute 0x0012 100 100 000 Old_age Always - 14

175 Unknown_Attribute 0x0003 100 100 010 Pre-fail Always - 16

192 Power-Off_Retract_Count 0x0012 100 100 000 Old_age Always - 0

194 Temperature_Celsius 0x0022 040 100 000 Old_age Always - 40 (Lifetime Min/Max 30/60)

197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0

240 Head_Flying_Hours 0x0013 100 100 050 Pre-fail Always - 0

170 Unknown_Attribute 0x0003 100 100 010 Pre-fail Always - 68724981813

173 Unknown_Attribute 0x0012 100 100 000 Old_age Always - 9070254639

SMART Error Log Version: 1

ATA Error Count: 14 (device log contains only the most recent five errors)

CR = Command Register [HEX]

FR = Features Register [HEX]

SC = Sector Count Register [HEX]

SN = Sector Number Register [HEX]

CL = Cylinder Low Register [HEX]

CH = Cylinder High Register [HEX]

DH = Device/Head Register [HEX]

DC = Device Command Register [HEX]

ER = Error register [HEX]

ST = Status register [HEX]

Powered_Up_Time is measured from power on, and printed as

DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,

SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 14 occurred at disk power-on lifetime: 4332 hours (180 days + 12 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:

ER ST SC SN CL CH DH

-- -- -- -- -- -- --

40 51 00 b8 d8 df e0 Error: UNC at LBA = 0x00dfd8b8 = 14670008

Commands leading to the command that caused the error were:

CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name

-- -- -- -- -- -- -- -- ---------------- --------------------

c8 00 08 b8 d8 df e0 08 00:21:07.200 READ DMA

ec 00 00 00 00 00 a0 08 00:21:07.200 IDENTIFY DEVICE

ef 03 46 00 00 00 a0 08 00:21:07.200 SET FEATURES [Set transfer mode]

ec 00 00 00 00 00 a0 08 00:21:07.200 IDENTIFY DEVICE

c8 00 08 b8 d8 df e0 08 00:21:07.200 READ DMA

Error 13 occurred at disk power-on lifetime: 4332 hours (180 days + 12 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:

ER ST SC SN CL CH DH

-- -- -- -- -- -- --

40 51 00 b8 d8 df e0 Error: UNC at LBA = 0x00dfd8b8 = 14670008

Commands leading to the command that caused the error were:

CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name

-- -- -- -- -- -- -- -- ---------------- --------------------

c8 00 08 b8 d8 df e0 08 00:21:07.200 READ DMA

ec 00 00 00 00 00 a0 08 00:21:07.200 IDENTIFY DEVICE

ef 03 46 00 00 00 a0 08 00:21:07.200 SET FEATURES [Set transfer mode]

ec 00 00 00 00 00 a0 08 00:21:07.200 IDENTIFY DEVICE

c8 00 08 b8 d8 df e0 08 00:21:07.200 READ DMA

Error 12 occurred at disk power-on lifetime: 4332 hours (180 days + 12 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:

ER ST SC SN CL CH DH

-- -- -- -- -- -- --

40 51 00 b8 d8 df e0 Error: UNC at LBA = 0x00dfd8b8 = 14670008

Commands leading to the command that caused the error were:

CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name

-- -- -- -- -- -- -- -- ---------------- --------------------

c8 00 08 b8 d8 df e0 08 00:21:07.200 READ DMA

ec 00 00 00 00 00 a0 08 00:21:07.200 IDENTIFY DEVICE

ef 03 46 00 00 00 a0 08 00:21:07.200 SET FEATURES [Set transfer mode]

ec 00 00 00 00 00 a0 08 00:21:07.200 IDENTIFY DEVICE

c8 00 08 b8 d8 df e0 08 00:21:07.200 READ DMA

Error 11 occurred at disk power-on lifetime: 4332 hours (180 days + 12 hours)

When the command that caused the error occurred, the device was active or idle.

.....

Контроллер/шлейф

Шлеф менялся так что наверно мать будь она неладная ....

не факт, кстати хот-свапа там нет случаем? Если есть, может бекплейт, и еще рекомендую рассмотреть питание, какой там БП, как обвешан вениками, какие процы, не печки ли?

Нет там тока 2 харда хосвопов нет. Рейдов тоже. Питания должно хватать учитывая то что я заменил обычный хард на ссд. Хотя второй хард не глючит правда они итак и не юзаеться как первый.